Dear fellow mCPX Users,
I am proud to bring to you guys this great news. As the title has mentioned, the MCPX is now able to be Governed by a third party ESC...
The current method of Governing that is accomplished at the moment is a
"Reactive" Governor where the MCPX would increase\decrease its power once the rpm falls below the pre defined RPM...
Using this method, known as flashing of the ESC, we now are also able to use the ESC to run a tail and main brushless set up without the need for a convertor. The exact potential as described by the guys a helifreak are as follows,
The code supports:
- Brushless tail. Get rid of that heavy SR120 tail motor.
- Governed main. Get consistent cyclic and collective response in hard maneouvers.
Other features are:
- Parameters programmable from TX
- Optional pitch to tail mix in governed mode.
- Allows build of ultralight main and tail ESCs (<0.4gram).
- Both v1 and v2 3in1 boards are supported.
This is a completed model that i made to make sure this system works prefectly and it does...
By xuen7 at 2012-04-15
By xuen7 at 2012-04-15
By xuen7 at 2012-04-15
Yea i its kinda messy and all.. didnt wanna tighten the wires and wasnt confident enough then to re solder all over again.. much better after touching up.
By xuen7 at 2012-04-15
By xuen7 at 2012-04-15
The brushless tail...
By xuen7 at 2012-04-15
Latest Microheli Advanced X frame and Advanced X swashplate, Titanium Main shaft and ...
By xuen7 at 2012-04-15
Finally my very own mCPX Mama-shop that recently opened up right beside my bed... ( used to be ex-gf make up area... so yea also got spare cash from being single to spend on my hobbies.. )
By xuen7 at 2012-04-15
By xuen7 at 2012-04-15
I am proud to bring to you guys this great news. As the title has mentioned, the MCPX is now able to be Governed by a third party ESC...
The current method of Governing that is accomplished at the moment is a
"Reactive" Governor where the MCPX would increase\decrease its power once the rpm falls below the pre defined RPM...
Using this method, known as flashing of the ESC, we now are also able to use the ESC to run a tail and main brushless set up without the need for a convertor. The exact potential as described by the guys a helifreak are as follows,
The code supports:
- Brushless tail. Get rid of that heavy SR120 tail motor.
- Governed main. Get consistent cyclic and collective response in hard maneouvers.
Other features are:
- Parameters programmable from TX
- Optional pitch to tail mix in governed mode.
- Allows build of ultralight main and tail ESCs (<0.4gram).
- Both v1 and v2 3in1 boards are supported.
This is a completed model that i made to make sure this system works prefectly and it does...
By xuen7 at 2012-04-15
By xuen7 at 2012-04-15
By xuen7 at 2012-04-15
Yea i its kinda messy and all.. didnt wanna tighten the wires and wasnt confident enough then to re solder all over again.. much better after touching up.
By xuen7 at 2012-04-15
By xuen7 at 2012-04-15
The brushless tail...
By xuen7 at 2012-04-15
Latest Microheli Advanced X frame and Advanced X swashplate, Titanium Main shaft and ...
By xuen7 at 2012-04-15
Finally my very own mCPX Mama-shop that recently opened up right beside my bed... ( used to be ex-gf make up area... so yea also got spare cash from being single to spend on my hobbies.. )
By xuen7 at 2012-04-15
By xuen7 at 2012-04-15
Comment