THIS POST GOT EATEN UP AND DESTROYED, I SPENT 2 HOURS MEASURING SHAFTS AND DIAMETERS WITH CALIPERS AND TYPING THIS OUT ON MY PRECIOUS SUNDAY AFTERNOON, ARE YOU KIDDING ME!!!!! I HAVE TO MEASURE IT AGAIN?!?!?! NO AUTOSAVE?!?!?!?!?!
Ok, but enough of that.
PLEASE READ HOW TO DEAL.
Pictures:
IC props:
Electric props:
Folding props:
Prop adapters:
Wheels in pairs:
Wheels in 5 packs:
Wheels in 3 packs:
Free stuff:
Ok, but enough of that.
PLEASE READ HOW TO DEAL.
- SMS me. Don't PM. My number: ninety-eight, 24, ninety, 10.
- Quote item number below.
- Self collect at my place.
- Props for IC engines - $3 each. These tend to have thicker hubs and weigh a bit more than electric props. You can run them in your electrics but the additional weight will affect spool up. Overall current draw doesn't seem to be much affected at all.
- Xoar 14x8. 6mm shaft hole.
- APC 6.5x6.5. Seems to be a 4.5mm shaft hole.
- APC 8x4. 6mm shaft hole.
- APC 7x9. Seems to be a 4.5mm shaft hole.
- Electric props - $3 each. Don't try to use these on your IC engines, they might fail!
- GWS-style slow flyer 9x5, NIB. Comes in a pack of two, price includes both.
- Unknown brand slow flyer 8x4.5, NIB. Comes in a pack of two, price includes both.
- Unknown brand slow flyer 8x4.5, with carbon for stiffness. One is used, therefore one left in pack.
- APC 8x6E, NIB.
- APC 13x6.5E, NIB.
- APC 13x8E, NIB.
- APC 8x3.8 slowfly, packet opened but never used before.
- APC 6.5x5 pylon racing prop, NIB.
- APC 16x8E, NIB.
- APC 6x5.5E, NIB.
- EMP 6x5, packet opened but never used before.
- TGS 14x7, NIB.
- APC 8x8, packet opened but never used before, let me know if you need the APC shaft adaptors.
- Turnigy 14x8 wood, new. 5mm shaft hole.
- Master airscrew 6.5x4. Never used, but out of packet.
- Master airscrew 7x4. Used a couple of times, no damage.
- APC 15x6, used once, tiny chips on one side.
- APC 12x6, used once, no damage.
- Turnigy 14x7 wood. I have TWO of these. One is BNIB, one is opened but unused. Shaft hole 8mm. This listing is for the BNIB one.
- Turnigy 14x7 wood. This listing is for the opened one.
- Folding props - $3 each. Not sure why I have these.
- 6.5x4, for 3mm shaft. I have TWO of these. One has its blades reversed for pusher configuration. You'll want to reverse it back for tractor configuration. Never used.
- 6.5x4, for 3mm shaft.
- Prop adaptors - $2 each.
- 5mm prop shaft, 3mm motor shaft, collet style.
- 6mm prop shaft, 4mm motor shaft, collet style.
- 6mm prop shaft, 4mm motor shaft, collet style.
- 6mm prop shaft, 4mm motor shaft, collet style.
- 6mm prop shaft, 3mm motor shaft, collet style.
- 6mm prop shaft, 3mm motor shaft, collet style, blue anodized.
- 6mm prop shaft, 3mm motor shaft, grub screw style.
- Wheels - $2 per pair. I had axle shaft sizes here, but it got deleted and I don't care now. Most of the holes are small so you have to drill, but it will be fine for wire landing gear. Use a drill bit you don't care about, plastic tends to melt and stick to your bit.
- GWS 85mm ultra light wheels.
- GWS 65mm ultra light wheels.
- 32mm, with landing gear wires attached. I think it came from an old FMS mini warbird.
- 40mm, white solid hub.
- 55mm, white solid hub. This one has 4mm hole, quite big.
- 60mm, white 5 spoked hub.
- 80mm, grey solid hub.
- Dubro Treaded Lightweight Wheel. 57mm, 4mm axle.
- Wheels - $3 per triple pack. 3 wheels per pack. All these are NIB.
- 45mm. White solid hub.
- 55mm. White solid hub.
- Wheels - $4 per 5-pack. 5 wheels per pack. All these are NIB.
- 45mm. Grey solid hub.
- 50mm. Grey solid hub.
- 60mm. White solid hub.
- 65mm. White solid hub.
- Free stuff!
- Some kind of folding prop holder for 3mm prop shafts.
- Some kind of control horn for large foamies.
- Single wheels of 100, 90, 80 and 60mm diameter.
Pictures:
IC props:
Electric props:
Folding props:
Prop adapters:
Wheels in pairs:
Wheels in 5 packs:
Wheels in 3 packs:
Free stuff:
Comment