HIROBO SCEADU EVO 50
HPM, 401 gyro, futaba S9253 tail servo,S9402Pitch servo, S3305 Roll Servo, S3001 throttle servo,Futaba carbon fins, 600mm wooden blades.
(but got Chipped heat sink on engine, Completely working, repaired frame on the front skid mount. )
( Basic kit alone cost $700 , minus all servos, gyro and engine)
Free 1.5 Gallon of Coolpower 20% (cost $33 per gallon )
+Thunder tiger hi torque starter (bought at $80)
+ one way bearing starter shaft ( Cost $40 )
+ electric fuel pump (cost $20 )
+ Kyosho EP caliber M24 RTF set(mode 2 tx), requires change of tail rotor motor i think. (bought at $500 when new ) ok ok condition only .
Ok, throw in Futaba TX module 29mhz . ( 30.00 crystal , rare )
Futaba RX module,PCM 1024, 6 channel 29mhz ( 30.00, rare ) = a set cost easily more than $150.
Also free DC switching power supply output t= 16v ,3.5 amp ( for the batt charger below )
KO PROPO – BX-213MH NI CAD/NI MH (bought at $180 when new)
Rest of the parts rebuild during last stupid crash of my evo due deteriorated fuel line in tank.
ALL above for =$ 1200 (to be sold as a bundle only and no less )
Selling urgent due last minute posting to US. No time to slowly sell.
Good for lao jiaos to buy and restore to tip top condition and resell for profit or to tempt new comers to the hobby ). Feel free to drop by my place to take a look and try to ask for more stuffs( trying to clear stuffs in my place too ). But place is fixed. Thanks
Will provide courtesy sending of the stuffs to ur place, free ride too if deal. On a car , obviously. But , pls come urself to take a look. ( I stay at pasir ris , near downtown east )
Drop me a reply , or sms or call me @ 97683387.
HPM, 401 gyro, futaba S9253 tail servo,S9402Pitch servo, S3305 Roll Servo, S3001 throttle servo,Futaba carbon fins, 600mm wooden blades.
(but got Chipped heat sink on engine, Completely working, repaired frame on the front skid mount. )
( Basic kit alone cost $700 , minus all servos, gyro and engine)
Free 1.5 Gallon of Coolpower 20% (cost $33 per gallon )
+Thunder tiger hi torque starter (bought at $80)
+ one way bearing starter shaft ( Cost $40 )
+ electric fuel pump (cost $20 )
+ Kyosho EP caliber M24 RTF set(mode 2 tx), requires change of tail rotor motor i think. (bought at $500 when new ) ok ok condition only .
Ok, throw in Futaba TX module 29mhz . ( 30.00 crystal , rare )
Futaba RX module,PCM 1024, 6 channel 29mhz ( 30.00, rare ) = a set cost easily more than $150.
Also free DC switching power supply output t= 16v ,3.5 amp ( for the batt charger below )
KO PROPO – BX-213MH NI CAD/NI MH (bought at $180 when new)
Rest of the parts rebuild during last stupid crash of my evo due deteriorated fuel line in tank.
ALL above for =$ 1200 (to be sold as a bundle only and no less )
Selling urgent due last minute posting to US. No time to slowly sell.
Good for lao jiaos to buy and restore to tip top condition and resell for profit or to tempt new comers to the hobby ). Feel free to drop by my place to take a look and try to ask for more stuffs( trying to clear stuffs in my place too ). But place is fixed. Thanks
Will provide courtesy sending of the stuffs to ur place, free ride too if deal. On a car , obviously. But , pls come urself to take a look. ( I stay at pasir ris , near downtown east )
Drop me a reply , or sms or call me @ 97683387.
Comment