6g Servo Offer!!!

[Wish]

Selling the following OEM 6g Servo. Will provide 7 days warranty from time of purchase. If you do not find this servo better then the China made "BLUE or GREY" color servo that you always use, simply return me for refund during the warranty period. No question asked.

Spec as follow:

Torque: 0.7kg /4.80V or 1.0kg/6.0V
Respond Time: 0.11s.cm /60 degree
Weight: 6.00g with universal/JR type connector
Special Offer : S$15/= each < U.P. = S$22 >

After warranty period over, you can still trade in your used servo( any condition) to get $3 discount.

Gear set available if you do not feel like trade in.

Will provide delivery for order 4pcs and above only. ( Petrol is too expensive recently... hope you guys understand... )

Also, I am looking for Retailer/Distributor that can purchase in qty. Please pm me if you are interested. Price satisfaction guarantee!!

[Wish]

Upzzz!

Full Spec for thise servo:

Supply voltage: 4.8V/6.0V
Speed: 0.10sec/60° No load running
Torque: 0.7kg.cm/1.0Kg.cm
Angle: 40°/one side pulse TRAVELLING400usec
Direction: Clock wise/pulse travelling 1500to 1900usec
Supply current: 1mA/100mA/operating current
Dead band drain: 10uses
Connector wire length: 150mm
Size: 21.2x11.4x19.5mm
Weight: 6g with JR connect

[Wish]

Dear All,

Servo temporary sold out. Next batch coming in end next week. Will keep you guys informed.

Thank you very much for your support!

Happy Flying!!

[Wish]

Hi all,

New batch servos are in, please PM me if you are interested. All feedback are goods so far and no return.

Happy Flying!

[headspeed]

Hi all,

New batch servos are in, please PM me if you are interested. All feedback are goods so far and no return.

Happy Flying!

does it come with servo horn?

[Wish]

does it come with servo horn?

Hi,

Yes, it does come with 2 standard " + " horns.

Thanks!

[mugenrsg]

sorry i'm new, jus wana check howz this servo compare to hitec hs55 interms of performance? Me wana get servos for slowstick, are ya servos suitable?

[Wish]

Hi mugenrsg,

PM sent.

Thanks!

[Wish]

.

[Wish]

Dear all,

I have received many enquiries if I could provide delivery for order below 4pcs...To make thing easier, I will mail the parts to you if you can provide me your home address. You can transfer the total amount to my account with $2 extra (need to buy special envelope to protect the servo) via any DBS/POSB ATM.

Let me know if this is workable. Thanks!

Happy flying!

[Wish]

I have found out some of the servo horn screws provided by the manufacturer are under size...

Please kindly PM me your address if your servo purchased is having the same problem, I will mail you the replacement once I receive the new screws from the manufacturer.

Sincerely apologize for all the inconvenience caused!

[Wish]

New Items Add On!

3D POP FLYER PITTS

Wingspan: 29",
Length: 29" ,
275-1/2” wing area,
Flying weight: 7-1/4 oz( Depends on set up ).

With a wing loading of less than 4 oz. per sq. ft. this airplane fly extremely slow and stable. Increase the throttle and see it fly vertical, with small degree of aileron apply, see this eyecatching beautiful biplane roll vertically and nicely. Experience flyer can also perform acrobatic like hovering, knife edge snap roll, half snap.. or any imagination you can think of.
Airplane is made of 5mm printed profile depron and pre-cut for easier assembly. Flyer can also laminate the depron body or wing using normal transparant scotch tape. Carbon fibers provided to reinforce the wing’s leading and trailing edges. Landing gear included. Large control surfaces assure crisp response to any control input. Fly in a small area like your front yard. Very good B/W photos illustrated manual. Build in 3-4 hours.

You need the following items to complete the plane:
4 channels TX for Aileron, Elevator, Rudder and Throttle
2cells or 3 Cells 1000mAH -1300mAH(10C and above )
Brushless or Brush 370 with C Gear
9050 - 1147 propeller
10-25A ESC depends on power set up.
3-4 servo

OFFER PRICE: SGD59/= Limited set only.

[Wish]

Unbreakable EPP 3D GEE BEE

Unbreakable EPP 3D Gee BEE

Wing Span: 850mm
Length : 810mm
Material: EPP
Kits Weight: 110g

Rudder and Aileron of the EPP Gee Bee were strengthen with light weight carbon rods for crisp response. 3 - 4 hours required to complete the plane, filament tape and hardware for servo linkage provided.

Best 3D trainer for 3D lover.

You need the following to complete the plane:
(1) 4 Channel TX
(2) Brushless Motor with low RPM
(3) 1047 - 1147 prop
(4) 10A-18A ESC
(5) 3 Cells LiPo (880mAH - 1300mAH)
(6) RX
(7) 3 - 4 servos
(8) Foam Safe Paint

Offer Price for ARF kit: S$89/= (Limited Set)

[Wish]

Offer still available (while stock last only).

Free gift: Buy 5 servos to get one 12" servo extension cable for free. Please SMS me if you are interested.

Happy flying!

Wish
96659352

[Wish]

Upzz!!

Offer still on!!