Announcement

Collapse
No announcement yet.

JGF500TH Bell Replacement

Collapse

Zenm Tech Pte Ltd

Collapse

Visit Zenmtech at rc.zenmtech.com

X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    JGF500TH Bell Replacement

    Anyone knows where can i find the 500TH bell replacement in Singapore? I know that JGF website do sell it but i was hoping to find LHS selling it.. Anyone knows?
    AR Drone 2.0
    Walkera Ladybird Micro Quad
    Jr XG8 Tx (Mode 1)
    RG831B Rx

    sigpic

    #2
    What happened? You were using it just now. Or post buy a 2nd hand or burnt 500TH.

    Comment


      #3
      Ken told me the shaft is bent and not very safe to fly.. So i thought changing the whole bell lo.. Can anyone advise me on the shipping stated in JustGoFly website? They say its recommended to use EMS for shipping to Singapore but they also have other types of shipping for international shipping. So MUST i use EMS or i can choose other types of shipping?

      The EMS cost $28 while normal international shipping cost only $12..
      AR Drone 2.0
      Walkera Ladybird Micro Quad
      Jr XG8 Tx (Mode 1)
      RG831B Rx

      sigpic

      Comment


        #4
        Any grudge screw securing the shaft? If have, maybe can remove the shaft and find a same diameter one? Should be 3.17mm shaft right? How you play till shaft bent Maybe can go back to the LHS if its bought brand new?

        Comment


          #5
          On the outside i couldn't find the grub screw lehz.. I know can replace the Shaft only but which LHS selling 3.17mm shaft? Thanks for the input!

          Will open the motor and see..
          AR Drone 2.0
          Walkera Ladybird Micro Quad
          Jr XG8 Tx (Mode 1)
          RG831B Rx

          sigpic

          Comment


            #6
            Can try Jethobby or RCE which will be opened tomorrow. Got to note if the entire shaft is same diameter or the external and internal length is of same diameter, if different then might be difficult to find replacement.

            Comment


              #7
              I just checked with RCE, they dont have bell replacement for JGF motors.. Anyway, the shaft is 4mm den goes down to 3.17mm for the pinion.. So i think its virtually impossible to get shaft replacement of the same diameter.. Anyway i've got a PM from one fellow member selling the Bell and shaft for $30.. Might be getting from him.. Thanks guys!
              AR Drone 2.0
              Walkera Ladybird Micro Quad
              Jr XG8 Tx (Mode 1)
              RG831B Rx

              sigpic

              Comment


                #8
                $30?Top up another 50 get a Scorpion

                Comment


                  #9
                  2nd hand scorpion for $50? Haha.. Who is selling it? Oh ya, i jus Sms u..
                  AR Drone 2.0
                  Walkera Ladybird Micro Quad
                  Jr XG8 Tx (Mode 1)
                  RG831B Rx

                  sigpic

                  Comment


                    #10
                    Your sms is emtpy leh

                    Comment


                      #11
                      Got 2 sms.. I accidentally sent the 1st one blank.. Haha.. Anyway, does motor have warranty?
                      AR Drone 2.0
                      Walkera Ladybird Micro Quad
                      Jr XG8 Tx (Mode 1)
                      RG831B Rx

                      sigpic

                      Comment


                        #12
                        Only got 1 blank sms from you The warranty part not sure, you have to speak to the LHS to find out.

                        Comment


                          #13
                          I saw in marketplace a JGF500TH selling at $40.. And u are the last poster.. So i sms asked if u brought it.. I sms the seller but he did not reply..
                          AR Drone 2.0
                          Walkera Ladybird Micro Quad
                          Jr XG8 Tx (Mode 1)
                          RG831B Rx

                          sigpic

                          Comment

                          Working...
                          X