If this is your first visit, be sure to
check out the Rules and Help. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Completed the conversion to sub-micro. However, overtrimmed the main blades the first time round! The instructions called for trimming the main blades by 65 mm... thats way too much. In the end the heli cant lift.
Awesome then passed me a set of used blades that i trimmed... about 30 to 40 mm... din measure! After that the heli was flying very stable. THANKS AWESOME!
After the conversion, becos of the higher head speed, the heli was very very stable. Also becos of the trimmed parts the battery lasted longer due to the reduced weight.
The heli also looks better and more 'sporty'... with the shortened skids. now if i can go get the huey shell... it would look really scaled. Better if done with the raised tail conversion.
The only drawback to the sub-micro is that it cant go very high. When i go full throttle, the heli hovers about 1 plus metre. I think for CPs, that would be a problem as u can just increase the pitch for more height. Now it is safer hovering at home!
Thanks for the link, vincopter & awesome for your blades! Will post pics of the completed heli soon.
Originally posted by VinCopter
Kam,
Check out the link, it is a Piccolo FP. Most of my sub-micro dimensions come from here,
After getting the stuff that is stated by Moveon, it seems my 4-in 1 doesn't makes any of your guys. Cos its a HB-T..
So i have decided on the following indivivual components to place inside my HB-T. I took out the 4in1 liao
Here are the selected components that i hope will work
Final Selection:
1)HFS-04MG Hitec 4chn receiver with crystal @ 35.010Mhz $53
2)Micro Piezo Gyro $50
3)ESC-GWS/ICS-300LI (i m not sure whether 1 is enough)
My Hangar:
Heli 1:T-REX 450SE (Hughes MD 500)
(SE-maiden 15/03/06)
(XL-maiden 16/10/05)
Heli 2:RAPTOR 50 TITAN
(TITAN-maiden 16/06/2006)
Heli 3:T-REX 500ESP (T-rex maiden 25/9/10)
(FLASHER 500-maiden 08/10/2009 R.I.P:09/08/10)
Heli 4:Flasher 250
(maiden 13/09/2010)
Airplane 1:GWS A-4SU SkyhawkFor Sale Airplane 2:GWS P-40N WarHawk RAAF maiden flight 20/08/10 For Sale
Transmitter:
JR 9XII(XPS 2.4)
Its all fun & games till the bills come..
After getting the stuff that is stated by Moveon, it seems my 4-in 1 doesn't makes any of your guys. Cos its a HB-T..
So i have decided on the following indivivual components to place inside my HB-T. I took out the 4in1 liao
Here are the selected components that i hope will work
Final Selection:
1)HFS-04MG Hitec 4chn receiver with crystal @ 35.010Mhz $53
2)Micro Piezo Gyro $50
3)ESC-GWS/ICS-300LI (i m not sure whether 1 is enough)
bro, i think u need 1 more GWS ICS-50 for the tail motor.. check out here if ure going separates..
After getting the stuff that is stated by Moveon, it seems my 4-in 1 doesn't makes any of your guys. Cos its a HB-T..
So i have decided on the following indivivual components to place inside my HB-T. I took out the 4in1 liao
Here are the selected components that i hope will work
Final Selection:
1)HFS-04MG Hitec 4chn receiver with crystal @ 35.010Mhz $53
2)Micro Piezo Gyro $50
3)ESC-GWS/ICS-300LI (i m not sure whether 1 is enough)
Wow!I think your honey bee had coming a UH-1 BEE liao
Comment