If this is your first visit, be sure to
check out the Rules and Help. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Hey by the way I found a kick butt canopy that totally changed the shape of the trex 700..the one that comes with it looks nice too but this is really killer.
Whiplashing soon?
Crash records counter
JR Vibe 50: 01
Trex600N Pro: 01
Kasama Srimok 90: 01
TT Raptor 50: 10
TT Raptor 90 3D: 01
MA Fury 55: 01
Governor sensor
Used the tj pro 30/50 mount and had to cut it down quite a lot. Not sure if my sensor is going to hold up under this type of mounting method. Only time will tell. Spacer was required to space the sensor out from the frame.
Very bare main frame.
Only complain here is that the holes in the carbon frames are not very well cleaned. The rest fit very well and al was square on first attempt. The manual assumed that nobody will run a battery switch, but I do. Only after building the whole heli then I realise you should put the switch in BEFORE building the frame.
Tail Assembly
I opted to use the metal boom.
Not sure how much the tail case should clamp on the boom, but on mine, if you tighten it down too much, it bends the tail fin. Photo shown w/o tail fin mounted.
Tail case did not require any assembly and tail grip/hub was VERY VERY well loctited.
The tube torque gear in the main frame appears to be just held on by a pin. Not sure if it will fly out like in the raptor 90. Hopefully not.
Engine/Fan hub
Again, no drama here. The prop nut required a long reach socket. Everything went on just nicely as it should. Fan hub is pushed in, then clamp on with two set screws. Everything fell in VERY nicely. Zero adjustment was required, but it better be, because there doesn't appear to be any room for adjustment in this kit.
Servos installation/CCPM mixer arms
Elevator servo mount required a bit of cutting to clear the wires. The linkage rod length in the manual for the aileron and pitch mixer arm to swash is a few turns too short. I increased it so that the swash is flat when everything is centered. I am getting 0.5 degree pitch at 50% pitch curve, -14 at 0% and +13 at 85%. Will need some more adjustment when I really have time. For now I suppose it should work for maiden. Pitch mixing % on my radio is 45%, is it a bit too low?
The control shaft on the ccpm mixer required 2 shim. After pulling and playing around, the main shaft also reqired shimming, just the thinest one got it tight. Suprisingly, I did not have the problem of "thinnest shim being too thick" issue that a lot are having.
Ino-lab 760 for cyclic, BLS251 for tail and hitec 325 for throttle as I am too lazy to pull out the 9254 from the raptor.
Boom slotted in. The torque required a lot of oil and force to get it moving into the tail boom. I made the mistake of securing the tail mount case to the main frame before putting in the boom. Boom support and fin mounting was also pretty straight forward. It is not quite as small as some have put it to be. It is actually still pretty big compared to the raptor.
Muffler mounted
Just some tips for anyone building one now. Do the throttle servo linkages before mounting the muffler. Use the lower fuel line hole if you are using a YS, the top one is blocked by the regulator. Mount the elevator servo arm BEFORE mounting the whole assembly onto the heli. Mount the regulator switch before putting the frame halfs together.
All had been smooth sailing, but when I reached the canopy and tail control rod part...there are some tolerance/alignment problems. Not sure if its my fault or manufacture issue...will see if I can sort them out before posting.
Hey by the way I found a kick butt canopy that totally changed the shape of the trex 700..the one that comes with it looks nice too but this is really killer.
wow nice canopy.....Wonder if there is one for the 600N
YOu FLy, You CRASH, YOU LEARN..
Mini Titan
JGF500th
CC45
Hitec 65HB x 3
Futaba 9257
Futaba GY401
[U]colco lama v5[COLOR=Red]][COLOR=SandyBrown]
Align Trex600N Pro
JR PCM 9X II e-STATIONBC6
kong lipo
Dualsky
ace RC
x TREAM
Comment