Beam E4

[sookainian]

Got my Beam yesterday

Some sneek preview

Beautiful box, can't bear to throw it away




Note the canopy, new design.


Very nicely pack.

[CKS]

Flight review soon too?
what power options u gonna use?

I hope its not just another pretty face (heli..)

[sookainian]

CKS: I am planing to use Scorpion set up for my Beam. But for now, i will just use some cheap motor and ESC as i haven order them yet.



1st bag.


CNC belt guide pulley


CNC main shaft bearing block


CNC boom clamp




Two long screw used to secure the boom.


Upper & Lower carbon gyro mounting plate. You get to choose to mount your gyro inverted or upright


CNC motor mount

[Ivan M]

Is the canopy fibreglass or PC?

[mh3400]

Kenny, are u sure u flying small heli

[cyz0301]

small heli can train on his reflex next time fly his stratus even lower we got good show le

[sookainian]

Ivan M: The new canopy is plastic. They said that the plastic canopy is actually lighter then the old fiber canopy. And this new canopy can take crashs better.

mh3400: Of coz i am very sure

cyz0301: Not sure how true is it hahas



2nd bag. Beam's logo printed on the skids


I used a heat gun to heat the landing strut. So the skids will slide in easily.


Nylon comound landing skids


Bottom plate is screw onto the landing skids.


Main frame and bottom plate side by side.




CNC canopy mount standoff


Frame complete ! Stiff yet light

[Raven]

Yo take a nice pic of you new Beam and put in in your 14MZ manzzz....

Cheers

[sookainian]

Raven: This heli is to nice for my radio. I will need to gold plated my 14mz first



3rd bag.


The swashplate and bearing comes separately pack. Just slide it in and screw in the three screws provided.


Dont forget to loctite the linkage ball.


CNC Swash complete ! Very smooth finish + no play


Main gear and pulley gear


Autorotation unit. Note: Dual bearing auto-rotation unit


Loctite them ! Note: you can see the 2nd ball bearing from here.


Main gear complete !

[CKS]

I had the honour of seening this heli and RJX fly b 4 official release in local market (Gd thing about living near one of the vendor) .. carbon and fully bling out of the box at reasonable price

Waiting for you flight video/review!

[flybywire]

Thinking of getting one too. But I have not flown any heli before, really appreciate the E4 precision parts and no nonsense finishing.

[helichoo]

Beam heli assembly

Good job kenny,and very nice cool heli. if i can afford to by one ,i do it.

[Heli_fanatic]

Thinking of getting one too. But I have not flown any heli before, really appreciate the E4 precision parts and no nonsense finishing.

hoho i think u should get a simulator first before even thinking of 450 sized helis

[sookainian]

Everyone must be waiting to see this right ?

CNC rotor head. Comes pre assemble. Beam's logo is printed on the grips and hub


CNC seesaw mixing arm. In the menual they'll ask you to add some loctite before sliding the bearing in. But i skip that reason being is that it will be easier for me to maintain. I Can just knock the bearing out anytime with out the need of heating it.


But remember to loctite those screws.




CNC Washout arm. Remember not to over tighten the screw going thru the washout link. If not you will strip the plastic.


Almost complete...


CNC flybar control cage

[sookainian]

4th bag.


One piece CNC open tail case design


Dam easy to fix and maintain.
1. Just slide the 2 bearings onto the tail shaft.


2. Push the whole thing into the tail case. (add some loctite if you want on to the outter face of the bearing before sliding in)


3. Loctite the 2 screws and you are done. So simple


CNC slider comes preassemble too.


CNC tail. Is also preassemble.


A complete tail rotor assembly ready to be fited onto the heli