Announcement

Collapse
No announcement yet.

CP2 Bad Glitch

Collapse

Zenm Tech Pte Ltd

Collapse

Visit Zenmtech at rc.zenmtech.com

X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    CP2 Bad Glitch

    Hi guys,

    Need some help here, my cp2 is twitching like hell. Anyone know what happen? Some minor glitch when i bought it but now is the worst. I have tried to re-route the antenna here and there but still the same problem.



    Any advise please.

    #2
    look like it glitch onli when u touch the stick sia. i dunno oso why. tx not good?
    sigpic

    Helis:
    Heli 1: Trex 450SE V1
    Status: Fit
    Date of Operation: 27 JULY 08
    Specs: JGF 450TH + RCE-BL25G + GY401 + HS-65HB cyclics + HS81 tail
    Radio: Optic 6 + Electron6
    Batt: Zippy-H 3s 2200mah 20C

    Comment


      #3
      try extending the antenna.... was told by some experience flyers that you need to only extend the thin one to the fullest when doing range check or servos setting....

      also sometimes it may happen if you are using different brands of equipment for example JR TX with Hitec RX....

      Comment


        #4
        I've experienced this problems when the esky servo is faulty, causing a short circuit and thus the receiver screws up. unplug the servos and plug them one by one and try.

        Comment


          #5
          haha lucky you got your trex repaired right?

          forget about the problem and play with your trex lor
          sigpic
          What goes up must come down ... its a matter of how

          Comment


            #6
            same experience...servos twitching on my CP2...got 2 of them changed and it works OK...time to contact Aerosmith??

            Comment


              #7
              Originally posted by linhai
              haha lucky you got your trex repaired right?

              forget about the problem and play with your trex lor
              haha. yeah. trex repaired. but yst boom strike. but i midnight repaired again. haha. later gonna go fly too. but however, have some problem, when i punch my trex tail wag. not sure why.
              sigpic

              Helis:
              Heli 1: Trex 450SE V1
              Status: Fit
              Date of Operation: 27 JULY 08
              Specs: JGF 450TH + RCE-BL25G + GY401 + HS-65HB cyclics + HS81 tail
              Radio: Optic 6 + Electron6
              Batt: Zippy-H 3s 2200mah 20C

              Comment


                #8
                Originally posted by detach8
                I've experienced this problems when the esky servo is faulty, causing a short circuit and thus the receiver screws up. unplug the servos and plug them one by one and try.
                Hi,

                Seems okay with the servos. tried one by one, swap them and problem is more obvious on the rear 2 channels. Is it my 4 in 1?

                Comment


                  #9
                  nono not swap them, is unplug all and plug in only one

                  if it still glitches more likely your 4-in-1 receiver is problematic

                  just go ask round for a spoilt 4-in-1 that has same freq as yours, and swap the receiver portion and try again.

                  Comment


                    #10
                    Originally posted by detach8
                    nono not swap them, is unplug all and plug in only one

                    if it still glitches more likely your 4-in-1 receiver is problematic

                    just go ask round for a spoilt 4-in-1 that has same freq as yours, and swap the receiver portion and try again.
                    Thanks. Getting my second cp2 tomorrow so will try on it.

                    Comment


                      #11
                      2nd CP2? Wah..you hardcore CP2 fan

                      Comment


                        #12
                        Originally posted by dankoo
                        2nd CP2? Wah..you hardcore CP2 fan
                        Can't resist a good deal leh.

                        Comment


                          #13
                          Originally posted by detach8
                          nono not swap them, is unplug all and plug in only one

                          if it still glitches more likely your 4-in-1 receiver is problematic

                          just go ask round for a spoilt 4-in-1 that has same freq as yours, and swap the receiver portion and try again.
                          Hi all,

                          Turns out is my 4 in 1 giving all the glitch problem. Is it better to replace individually or should i change just the 4 in 1? Have heard the 4 in 1 is a house of everything but good for nothing...

                          Comment


                            #14
                            lol.. house of everything but good for nothing.. interestin.
                            but cp2 got space to go seperates?
                            Eflite Blade CX2 - 23 Feb 2007
                            HoneyBee CP2 - 01 Jan 2007
                            1st crash (CP2) - 02 Jan 2007
                            1st fire accident (battery) - 07 Jan 2007

                            Comment


                              #15
                              why not man
                              see my sig
                              i am flying on 2s...

                              Comment

                              Working...
                              X