Need Help Tompang Order from Offshoreelectrics

[Dragon Slayer]

Dear Brudders;

Need some favour from any one of you here going to make an order from offshoreelectrics:

I just need 2 small items, 1 is a universal joint and the other is a 4mm drive shaft. If anyone going to order and dun mind to help, pls. pm me.

Thanks, and coffee on me.

[wtp]

Dear Brudders;

Need some favour from any one of you here going to make an order from offshoreelectrics:

I just need 2 small items, 1 is a universal joint and the other is a 4mm drive shaft. If anyone going to order and dun mind to help, pls. pm me.

Thanks, and coffee on me.

as for the 4mm driveshaft,i guess u can go to rotor to get their heli flybar rod which is 4mm diameter similar

[Mad Armour]

Dear Brudders;

Need some favour from any one of you here going to make an order from offshoreelectrics:

I just need 2 small items, 1 is a universal joint and the other is a 4mm drive shaft. If anyone going to order and dun mind to help, pls. pm me.

Thanks, and coffee on me.

I've just bought a 4mm steel rod from a harrware shop at Kelantan Road. 3' x 4mm diameter for $2.

[Dragon Slayer]

How to thread steel rod?

I've just bought a 4mm steel rod from a harrware shop at Kelantan Road. 3' x 4mm diameter for $2.

Hi;

Thanks for the advise. How do you thread the end of the rod, and cut to the correct length?

Thanks

[wtp]

Hi;

Thanks for the advise. How do you thread the end of the rod, and cut to the correct length?

Thanks

as for the die tools u can get it at various DIY shop or ntc

[Mad Armour]

Hi;

Thanks for the advise. How do you thread the end of the rod, and cut to the correct length?

Thanks

I use a threading die to thread. You can easily buy one from most hardware shops. As for cutting the rod, a hacksaw will come handy!

[Dragon Slayer]

I use a threading die to thread. You can easily buy one from most hardware shops. As for cutting the rod, a hacksaw will come handy!

Thanks to all the kind souls who offer help. Another qsn, where in Singapore can I get a universal joint 5mm threaded on one end (goes to engine) and 4mm on the other hand (over drive shaft)?

Thanks

[Mad Armour]

Thanks to all the kind souls who offer help. Another qsn, where in Singapore can I get a universal joint 5mm threaded on one end (goes to engine) and 4mm on the other hand (over drive shaft)?

Thanks

Can't help you on this. I've seen some engine - drive shaft coupler at NTC but they are not universal joint type.

BTW, what happened to your Proboat?

[Dragon Slayer]

Can't help you on this. I've seen some engine - drive shaft coupler at NTC but they are not universal joint type.

BTW, what happened to your Proboat?

Thanks...well...there was a restriction on how big a box USPS is able to accept, think it is 43". The proboat shockwave came in a 47" box, too big to be shipped. UPS shipping kills...so I got myself a nitro hammer instead.

[Mad Armour]

Thanks...well...there was a restriction on how big a box USPS is able to accept, think it is 43". The proboat shockwave came in a 47" box, too big to be shipped. UPS shipping kills...so I got myself a nitro hammer instead.

So you're on the quest to make your nitro Hammer faster so early on?

[Dragon Slayer]

So you're on the quest to make your nitro Hammer faster so early on?

Yup...I was. but bit of a bad luck (or was I asking for trouble) zipping within shipping lines which of course catches my prop and brought the hammer almost to the bottom....lucky there was foam inside to float the thing.

Thereafter, I experienced engine problems...i.e. engine roars over revs won't idle, once in water after a while slows and dies....

I almost wanted to return it back for warranty claims. Last draw, I stripped the entire engine (include carb) and rebuilt everything back. I then went to run it in again, miraculously, the thing didn't die and I had almost fiished running in with 5 tanks. Stay tuned!

[Mad Armour]

Yup...I was. but bit of a bad luck (or was I asking for trouble) zipping within shipping lines which of course catches my prop and brought the hammer almost to the bottom....lucky there was foam inside to float the thing.

Thereafter, I experienced engine problems...i.e. engine roars over revs won't idle, once in water after a while slows and dies....

I almost wanted to return it back for warranty claims. Last draw, I stripped the entire engine (include carb) and rebuilt everything back. I then went to run it in again, miraculously, the thing didn't die and I had almost fiished running in with 5 tanks. Stay tuned!

Shipping lines or fishing lines?

Anyway, sounds severe. Luckily you've managed to retune the engine.

[Dragon Slayer]

Shipping lines or fishing lines?

Anyway, sounds severe. Luckily you've managed to retune the engine.

Hehe...too excited...shipping lines in PP! Nah...it is fishing lines. Dunno why the fishermen were still there after 2 while I was running my hammer...I also paiseh kana his line. He was quite pissed off....cos the other fishermen suan him (and of course me) by simply saying..."WOW...big FISH!"

[Mad Armour]

Hehe...too excited...shipping lines in PP! Nah...it is fishing lines. Dunno why the fishermen were still there after 2 while I was running my hammer...I also paiseh kana his line. He was quite pissed off....cos the other fishermen suan him (and of course me) by simply saying..."WOW...big FISH!"

Best is to play in the middle of the pond, not near the cafe.