Announcement

Collapse
No announcement yet.

Align M480L / M690 Flyer..

Collapse

Zenm Tech Pte Ltd

Collapse

Visit Zenmtech at rc.zenmtech.com

X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Align M480L / M690 Flyer..

    Any one flying the above mention multi rotor ?
    YOu FLy, You CRASH, YOU LEARN..

    Mini Titan
    JGF500th
    CC45
    Hitec 65HB x 3
    Futaba 9257
    Futaba GY401
    [U]colco lama v5[COLOR=Red]][COLOR=SandyBrown]
    Align Trex600N Pro


    JR PCM 9X II
    e-STATION BC6
    kong lipo
    Dualsky
    ace RC
    x TREAM

    #2
    I have a 480.
    Too many helis!

    Comment


      #3
      Originally posted by ah_liang View Post
      I have a 480.
      this quad no fun at all cos it's basically frozen in the air regardless of wind conditions...with this model, methinks align simply blew every other system out of the market...including the white thing that flies away.
      Heli-ADDICTION:
      Mikado Logos, RaptorG4s, X7F, 600ESP...
      JUST one more Logo...for the month.

      Comment


        #4
        I also have a 480.

        Comment


          #5
          Glade to know that I ain't the only one flying it.. let's share and learn from each other here.. BTW any one using a spectrum dx on it?
          YOu FLy, You CRASH, YOU LEARN..

          Mini Titan
          JGF500th
          CC45
          Hitec 65HB x 3
          Futaba 9257
          Futaba GY401
          [U]colco lama v5[COLOR=Red]][COLOR=SandyBrown]
          Align Trex600N Pro


          JR PCM 9X II
          e-STATION BC6
          kong lipo
          Dualsky
          ace RC
          x TREAM

          Comment


            #6
            Flying with 2 dsmx sats from my dx18
            Too many helis!

            Comment


              #7
              Anyone here flying it with a gimbal?

              Comment


                #8
                I fly with 14SG (sbus), G3-5D gimbal, Canon 6D, Align OSD/FPV transmitter, and Align 30C 6S 8500mAh Lipo.

                Comment


                  #9
                  Bro how you bind the 480 in failsafe.. me too have the same set up
                  YOu FLy, You CRASH, YOU LEARN..

                  Mini Titan
                  JGF500th
                  CC45
                  Hitec 65HB x 3
                  Futaba 9257
                  Futaba GY401
                  [U]colco lama v5[COLOR=Red]][COLOR=SandyBrown]
                  Align Trex600N Pro


                  JR PCM 9X II
                  e-STATION BC6
                  kong lipo
                  Dualsky
                  ace RC
                  x TREAM

                  Comment


                    #10
                    Originally posted by boo_saa View Post
                    Bro how you bind the 480 in failsafe.. me too have the same set up
                    If you are using Futaba Tx, it is very easy, just follow the instructions in the manual.

                    If you are using Spektrum Tx, try the following steps.

                    1. After you have assigned all the switches and the direction of all channels are set correctly. Connect the APS-M to the PC and run the setup program.
                    2. Power up the multicopter, and see that the APS-M is connected to the software.
                    3. Activate the "Home" switch (i.e. turn on Home switch), you should see that the software indicates the switch is in the "ON" region.
                    4. Increase (or decrease) the travel of the Home switch (at ON position) until you see the software indicates that the switch is in the "FS" region.
                    5. Turn off everything, and proceed to re-bind the TX and Rx. During the binding process, make sure the Home switch is in the "On" position before you turn on the Tx for binding.
                    6. After the binding process, adjust the travel of the Home switch "On" position back its normal value.

                    7. To verify if failsafe is working, connect the APS-M and run the PC software. Turn off the Tx to see if the software indicates Home switch is in FS region.

                    Comment


                      #11
                      Originally posted by nb8686 View Post
                      If you are using Futaba Tx, it is very easy, just follow the instructions in the manual.

                      If you are using Spektrum Tx, try the following steps.

                      1. After you have assigned all the switches and the direction of all channels are set correctly. Connect the APS-M to the PC and run the setup program.
                      2. Power up the multicopter, and see that the APS-M is connected to the software.
                      3. Activate the "Home" switch (i.e. turn on Home switch), you should see that the software indicates the switch is in the "ON" region.
                      4. Increase (or decrease) the travel of the Home switch (at ON position) until you see the software indicates that the switch is in the "FS" region.
                      5. Turn off everything, and proceed to re-bind the TX and Rx. During the binding process, make sure the Home switch is in the "On" position before you turn on the Tx for binding.
                      6. After the binding process, adjust the travel of the Home switch "On" position back its normal value.

                      7. To verify if failsafe is working, connect the APS-M and run the PC software. Turn off the Tx to see if the software indicates Home switch is in FS region.
                      Tks man.. Greatly appreciated..
                      YOu FLy, You CRASH, YOU LEARN..

                      Mini Titan
                      JGF500th
                      CC45
                      Hitec 65HB x 3
                      Futaba 9257
                      Futaba GY401
                      [U]colco lama v5[COLOR=Red]][COLOR=SandyBrown]
                      Align Trex600N Pro


                      JR PCM 9X II
                      e-STATION BC6
                      kong lipo
                      Dualsky
                      ace RC
                      x TREAM

                      Comment

                      Working...
                      X