Announcement

Collapse
No announcement yet.

3.6 g Servo + 2.8g receiver

Collapse

Zenm Tech Pte Ltd

Collapse

Visit Zenmtech at rc.zenmtech.com

X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    3.6 g Servo + 2.8g receiver

    For the weight concious...
    new product at Jet... check it out:


    Blue Arrow Micro Reciver
    This receiver is very light, barring of an antenna 80mm/0.7g, a connecter sockets crystal 0.2g and a shrink wrap 0.2g, it only weighs 2.8g.
    It is recommended to create for the Park and Yard flyers and Indoor Aircraft applications that require a reliable and short remote distance one.
    This receiver compatible with PPM transmitter: HITEC, FUTABA, JR, MULTIPLEX, AIRTRONICS and most other transmitters by change crystal.
    Specifications:

    * 1. Size : 25mmX15mmX8mm(0.98in x 0.59in x 0.3in).
    * 2. Weight: 0.098 oz or 2.8g (without antenna, connecter sockets crystal and shrink wrap).
    * 3. 5 channel, FM PPM operation.
    * 4. Transmitter compatible: HITEC, FUTABA, JR, MULTIPLEX, AIRTRONICS and most other transmitters.
    * 5. Reliable operation to 1000 feet.
    * 6. Current Draw: 10 MA @ 5 Volts.
    * 7. Input Voltage Rage: 5.0 Volts.
    * 8. Available frequency: channels 11 through 60.

    Misc Information:

    * Stock: Coming Soon
    * Category: Receiver, Servo & Accessories, Hot Deals

    huh

    #2




    Blue Arrow BA-TS 3.6g
    Torque: 0.4kg.cm(5.55oz.in)
    Micro planes, Hand launch gliders, Small electrics helicopters ect.
    Features:

    * The net weight of this servo is 3.6g. It can also be rebuilt into a lighter one. With the servo-case bottom removed or using the JST plug, the weight can be reduced to 3.3g. Use the enameled wire to connect, the weight can be reduced by 0.8g. Totally, the weight can be reduced by 1.1g, and finally, you only get a servo only at 2.5g.

    Specifications:

    * Supply voltage: 4.8V
    * Speed: 0.12sec/60° No load running
    * Torque: 0.4kg.cm(5.55oz.in)
    * Angle: 40°/one side pulse TRAVELLING400usec
    * Direction: Clock wise/pulse travelling 1500to 1900usec
    * Supply current: 1mA/100mA/opertating current
    * Dead band drain: 10uses
    * Connector wire length: 160mm
    * Size: 19.6x17.6x8mm
    * Weight: 3.6g(0.13oz)with JST connect /4.6g(0.16oz.)with JR,FUTABA connect /4.1g(0.14oz.) without connect.

    Misc Information:

    * Manufacturer: Blue Arrow
    * Stock: Coming Soon
    * Category: Receiver, Servo & Accessories, Hot Deals
    huh

    Comment


      #3
      wah!! The mother of all micros!!

      6g for a receiver + servo?!?!

      Power!! But reliable or not??

      Comment


        #4
        Originally posted by PhiBeR
        But reliable or not??
        Well at least we know "Jet is not run by Chan".....

        I really starting to like this quote!
        huh

        Comment


          #5
          Hi all,
          The Blue Arrow servos and receivers are reliable. Balsa Products USA is distributing them too.

          I have them too. I also have spares like servo horns, gears and case. My stocks are arriving next week. And my prices would be better.

          Have fun!
          I have seen them all.

          A mediocre r/c pilot who thinks that he is one top gun.

          A nerd looking and sick flyer who thinks that he is a great modeller.

          Greed that made a friend became a competitor.

          Comment


            #6
            I would love the lightweight servo but the speed is too slow for tail servo.

            Super-Hornet

            Comment


              #7
              What is the speed that is suitable for the tail servo? Could the speed of this 3.6g servo b suitable for other area on the micro heli?
              I have seen them all.

              A mediocre r/c pilot who thinks that he is one top gun.

              A nerd looking and sick flyer who thinks that he is a great modeller.

              Greed that made a friend became a competitor.

              Comment


                #8
                Hi mack

                I find that for tail servo, it should be 0.10 or lower. The lower the better.

                Super-Hornet

                Comment


                  #9
                  Just for infor and discussion this is what I have for the lightest Rc equipment beside the magnetic type.

                  CCP7 ESC + Westeck Rx + 2X Westeck linear servo = 10.5g

                  Comment


                    #10
                    Originally posted by Super-Hornet
                    Hi mack

                    I find that for tail servo, it should be 0.10 or lower. The lower the better.

                    Super-Hornet
                    Hmmm..
                    Which servos are 0.10 and below??
                    Most of the common ones i see are .12s..

                    Only HS50 is 0.09, but is it's torque is lower of coz..
                    Anymore more < 0.1s servos?

                    Comment


                      #11
                      loyn,
                      They are extremely light. I guess that they r expensive.

                      Right, what other servos r 0.10s and lower?
                      I have seen them all.

                      A mediocre r/c pilot who thinks that he is one top gun.

                      A nerd looking and sick flyer who thinks that he is a great modeller.

                      Greed that made a friend became a competitor.

                      Comment


                        #12
                        JR has 1 micro servo with a speed of 0.10
                        hitec has the hs50 0.09
                        SG50 from jethobby 0.10
                        GWS naro+f hp 0.10

                        I do remember reading somewhere of a servo with 0.08, but just can't recall which brand it was under

                        Comment


                          #13
                          hehe.. SHS has one that is listed as 0.00... but I won't buy it... cause I don't believe it is 0.00
                          huh

                          Comment


                            #14
                            Wow 0.00 .....you mean they dont move or so fast that cant be measured ..... speed of light ...... SHS.....sign

                            Comment


                              #15
                              This is the home page of Singapore Hobby Supplies Pte Ltd.



                              Sub Micro servo RCM-306
                              Weight: 6.66g
                              Torque: 0.8kg-cm
                              Speed: 0.00sec
                              huh

                              Comment

                              Working...
                              X